New energy electric vehicles are not new in the present, but there are not many people who truly understand them. Most of them still have doubts about the use of new energy electric vehicles, such as whether fast charging will damage the battery and reduce its service life. Can it be high speed? Is there a charging pole at high speed? Is the battery recyclable? In response to these problems, we will use professional knowledge to solve doubts for you. The first thing to be sure is that fast charging does have a great deal of damage to the battery. All of them have heard that electric cars have two types of charging methods: fast charging and slow charging. They also know that fast charging is much faster than slow charging. The difference between them is that they are directly charged with a DC charging voltage during fast charging, and the slow charging is performed by first converting the AC power into DC power and then boosting the voltage to the charging voltage of the battery for charging. Fast charge voltage is generally greater than the battery voltage, so the battery quality requirements are very high, and the battery under high current conditions of the reaction conditions are too severe harsh, far from the equilibrium state, there is a greater loss of battery life, The safety factor will drop significantly, so try to do it as little as necessary. Slow charging can be a good way to avoid these problems. Regarding whether or not electric vehicles can be charged on high speeds and high speeds, the answer is that electric vehicles can achieve high speeds as long as they can reach speeds above 60 kilometers per hour, but charging at high speeds is not yet widely used, and some high speeds can be quickly charged across the board. Such as the Beijing-Shanghai high-speed, the entire 1262 kilometers, an average of one fast charge station every 50 kilometers, the fastest electric car can be filled for 30 minutes, the price of 0.65-0.8 yuan per degree. Regarding whether the new energy electric car battery is recyclable, at present, our country has not yet officially introduced the relevant standards for the recovery of new energy car batteries, but only released the "electric car battery recycling technology policy", and new energy car companies put more energy Put in research and development, the enthusiasm for battery recycling is not high. For foreign countries, the new energy electric vehicle battery adopts a ladder utilization mode. By using a ladder to extend the life of a lithium battery, the purpose of cost reduction can be achieved. In other words, the power battery with good performance after retiring can still serve as an energy storage battery, and it can be sold to power generation companies, power grids, or companies that need to store energy through batteries to reuse them. New Energy Electric Vehicles emphasizes environmental protection and cannot allow waste batteries to drag on environmental protection. No matter whether it is the government or the enterprise, it must not only focus on development, but also have to take corresponding social responsibilities so that new energy vehicles can be truly environmentally friendly.
Conductive Quick Connector with double seal ring radial seal structure, rubber modified by O - ring, mainly for fluid and the physical, chemical properties of custom, prevent aging, corrosion, swelling; O - ring have intermediate spacer ring separated, two sealing rings of the corresponding event space, the rubber matrix bonding does not occur, the external O-ring using synthetic rubber, enhanced mechanical properties, prevent air aging. Sealing ring and a spacer ring through the outer ring of the elastic bayonet device firmly fixed in the shell, does not produce seal off and shift phenomenon produced. Greatly ensure the safety of the seal.
Quick Connector composed of a connector housing, O - ring, O - ring, a spacer ring, outer ring, a self-locking buckle, when another pipe adapter (male connector) insert joint, because of the self-locking buckle has certain elasticity with buckle fastener can connect the two connectors together, then pulled back, ensure that the installation in place so fast joint can play a role. Disassembly and maintenance as long as the first to promote the positive joint and press and hold the self-locking buckle at both ends of the buckle buttons, the self-locking expansion in the middle, you can easily pull out the connector, re connect forward should use SAE 30, heavy oil lubrication.
The electric conduction fast joint is mainly in the medium of methanol gasoline and ethanol gasoline.. It has the overall structure, the best sealing effect. Can work under pressure 10bar. The engine area temperature is suitable for the short time of the -40 up to +110 to reach the +150 degree (about half an hour).
Conductive Quick Connector Conductive Quick Connector,Conductive Connector,Automotive Fuel Line Quick Connector Linhai Shinyfly Auto Parts Co.,Ltd. , https://www.chinashinyfly.com
Little knowledge of large-scale words that 90% of people do not know electric car knowledge