A hot water pipe pump maintenance 1. Operational maintenance: (1) The inlet pipe must be filled with liquid, and the long-term operation of the hot water pipe pump in the cavitation condition is forbidden. (2) regularly check the motor current ??, must not exceed the motor current rating. (3) After long-running hot-water pipeline pump, due to mechanical wear, make the unit noise and vibration increase, should stop inspection, if necessary, replace the vulnerable parts and bearings, unit overhaul period is generally one year. 2 mechanical seal maintenance: (1) Mechanical seal lubrication should be clean without solid particles. (2) Mechanical seal is strictly prohibited in the case of dry grinding. (3) Before starting, you should coil the triumphal hot water pipeline pump (motor) a few times before starting, so as to avoid the graphite ring breakage damage caused by sudden start. (4) Tolerance seal leakage 3 drops / min. Otherwise, check. Second, hot water pipe pump failure and maintenance Symptoms cause of issue Method of exclusion 1 , hot water pipe pump no water a , import and export valves are not open, out of the pipeline blocked, runner impeller blocked. a , check, remove the blockage. 2 , hot water pipe pump flow is insufficient a , first press 1. reasons to check. a , first press 1. exclude. 3 , the power is too large a , more than the rated flow use. a , adjust the flow, off the small outlet valve. 4 , noise vibration a , unstable pipe support. a , a solid pipeline. 5 , motor fever a , traffic is too large, overloaded operation. a , off the small outlet valve. 6 , hot water pipe pump leaks a , mechanical seal wear. a , replace. Symptoms cause of issue Method of exclusion 1 , hot water pipe pump no water a , import and export valves are not open, out of the pipeline blocked, runner impeller blocked. a , check, remove the blockage. 2 , hot water pipe pump flow is insufficient a , first press 1. reasons to check. a , first press 1. exclude. 3 , the power is too large a , more than the rated flow use. a , adjust the flow, off the small outlet valve. 4 , noise vibration a , unstable pipe support. a , a solid pipeline. 5 , motor fever a , traffic is too large, overloaded operation. a , off the small outlet valve. 6 , hot water pipe pump leaks a , mechanical seal wear. a , replace. Aerobic Stepper,Cardio Stepper,Aerobic Step Board,The Step Aerobic Stepper Nantong Detian Fitness Equipment Co.,Ltd , https://www.detianfitnessequipment.com
b , the motor is running in the wrong direction, the motor phase loss is very slow.
c , suction tube leakage.
d , the pump is not filled with liquid, there is air in the pump chamber.
e , imported insufficient water supply, suction stroke is too high, the valve leaks.
f , pipe resistance is too large, improper pump selection.
b , adjust the motor direction, tighten the motor wiring.
c , tighten the sealing surface, remove leakage.
d , filled with liquid and open the exhaust valve, drain the air.
e , downtime, inspection, adjustment (water pipe or suction pipe with easy to use this phenomenon).
f , reduce pipe corners, re-select the pump.
b , pipes, pump impeller blockage, scale deposition, the valve opening is not enough.
c , the voltage is low.
d , impeller wear.
b , remove the blockage, readjust the valve opening.
c , regulator.
d , replace the impeller.
b , suction is too high.
c , pump bearing wear.
b , reduce.
c , replace the bearing.
b , liquid mixed with gas.
c , produce cavitation.
d , bearing damage.
e , the motor overload heating operation.
b , improve suction pressure exhaust.
c , reduce the degree of vacuum.
d , replace the bearing.
e , adjust press 5 .
b , rub rub.
c , motor bearing damage.
d , the voltage is insufficient.
b , check and exclude.
c , replace the bearing.
d , regulator.
b , sand or cracked pump body.
c , sealing surface is not flat.
d , Loose mounting bolts.
b , welding repair or replacement.
c , trimming.
d , fastening.
b , the motor is running in the wrong direction, the motor phase loss is very slow.
c , suction tube leakage.
d , the pump is not filled with liquid, there is air in the pump chamber.
e , imported insufficient water supply, suction stroke is too high, the valve leaks.
f , pipe resistance is too large, improper pump selection.
b , adjust the motor direction, tighten the motor wiring.
c , tighten the sealing surface, remove leakage.
d , filled with liquid and open the exhaust valve, drain the air.
e , downtime, inspection, adjustment (water pipe or suction pipe with easy to use this phenomenon).
f , reduce pipe corners, re-select the pump.
b , pipes, pump impeller blockage, scale deposition, the valve opening is not enough.
c , the voltage is low.
d , impeller wear.
b , remove the blockage, readjust the valve opening.
c , regulator.
d , replace the impeller.
b , suction is too high.
c , pump bearing wear.
b , reduce.
c , replace the bearing.
b , liquid mixed with gas.
c , produce cavitation.
d , bearing damage.
e , the motor overload heating operation.
b , improve suction pressure exhaust.
c , reduce the degree of vacuum.
d , replace the bearing.
e , adjust press 5 .
b , rub rub.
c , motor bearing damage.
d , the voltage is insufficient.
b , check and exclude.
c , replace the bearing.
d , regulator.
b , sand or cracked pump body.
c , sealing surface is not flat.
d , Loose mounting bolts.
b , welding repair or replacement.
c , trimming.
d , fastening.
Hot water pipeline pump maintenance and fault and maintenance